stack-orchestrator/docs/arista-scraped/ingress-and-egress-per-port-for-ipv4-and-ipv6-counters.md

Ingress and Egress Per-Port for IPv4 and IPv6 Counters

This feature supports per-interface ingress and egress packet and byte counters for IPv4 and IPv6.

This section describes Ingress and Egress per-port for IPv4 and IPv6 counters, including configuration instructions and command descriptions.

Topics covered by this chapter include:

• Configuration

• Show commands

• Dedicated ARP Entry for TX IPv4 and IPv6 Counters

• Considerations

Configuration

IPv4 and IPv6 ingress counters (count bridged and routed traffic, supported only on front-panel ports) can be enabled and disabled using the hardware counter feature ip in command:

`**[no] hardware counter feature ip in**`

For IPv4 and IPv6 ingress and egress counters that include only routed traffic (supported on Layer3 interfaces such as routed ports and L3 subinterfaces only), use the following commands:

Note: The DCS-7300X, DCS-7250X, DCS-7050X, and DCS-7060X platforms do not require configuration for IPv4 and IPv6 packet counters for only routed traffic. They are collected by default. Other platforms (DCS-7280SR, DCS-7280CR, and DCS-7500-R) need the feature enabled.

`**[no] hardware counter feature ip in layer3**`

`**[no] hardware counter feature ip out layer3**`

hardware counter feature ip

Use the hardware counter feature ip command to enable ingress and egress counters at Layer 3. The no and default forms of the command disables the feature. The feature is enabled by default.

Command Mode

Configuration mode

Command Syntax

hardware counter feature ip in|out layer3

no hardware counter feature ip in|out layer3

default hardware counter feature in|out layer3

Example

This example enables ingress and egress ip counters for Layer 3.

`**switch(config)# hardware counter feature in layer3**`

`**switch(config)# hardware counter feature out layer3**`

Show commands

Use the show interfaces counters ip command to display IPv4, IPv6 packets, and octets.

Example

`switch# **show interfaces counters ip**
Interface   IPv4InOctets    IPv4InPkts     IPv6InOctets    IPv6InPkts
Et1/1            0               0               0               0
Et1/2            0               0               0               0
Et1/3            0               0               0               0
Et1/4            0               0               0               0
...
Interface  IPv4OutOctets  IPv4OutPkts    IPv6OutOctets   IPv6OutPkts
Et1/1            0               0               0               0
Et1/2            0               0               0               0
Et1/3            0               0               0               0
Et1/4            0               0               0               0
...`

You can also query the output from the show interfaces counters ip command through snmp via the ARISTA-IP-MIB.

To clear the IPv4 or IPv6 counters, use the clear counters command.

Example

`switch# **clear counters**`

Dedicated ARP Entry for TX IPv4 and IPv6 Counters

IPv4/IPv6 egress Layer 3 (hardware counter feature ip out layer3) counting on DCS-7280SR, DCS-7280CR, and DCS-7500-R platforms work based on ARP entry of the next hop. By default, IPv4's next-hop and IPv6's next-hop resolve to the same MAC address and interface that shared the ARP entry.

To differentiate the counters between IPv4 and IPv6, disable arp entry sharing with the following command:

`**ip hardware fib next-hop arp dedicated**`

        Note: This command is required for IPv4 and IPv6 egress counters
            to operate on the DCS-7280SR, DCS-7280CR, and DCS-7500-R platforms.

Considerations

            - Packet sizes greater than 9236 bytes are not counted by per-port IPv4 and IPv6 counters.

            - Only the DCS-7260X3, DCS-7368, DCS-7300, DCS-7050SX3, DCS-7050CX3, DCS-7280SR,
                DCS-7280CR and DCS-7500-R platforms support the **hardware counter feature ip in** command.

            - Only the DCS-7280SR, DCS-7280CR and DCS-7500-R platforms support the **hardware counter feature ip [in|out] layer3** command.